Hey guys.
It's a pretty perfect skin, one issue I am facing is "GPU2 not present" on the right. I know I don't 2 GPU's.
Just some tiny details that are bugging me a little.
It's unchanged text file. Can someone please direct me as to where I would be able to disable this line and move the cpu details up to fill its spot.
I have already attempted just deleting what I believed what was the culprit but then the line was replaced with just a "%".
Then I just deleted the phrase in the quotation marks and then it became a 0.
Any help is appreciated.
Thank you
It is currently April 24th, 2024, 11:59 am
Help editting SK Neon Meters
-
- Posts: 2
- Joined: April 7th, 2021, 11:19 pm
-
- Posts: 2
- Joined: April 7th, 2021, 11:19 pm
Re: Help editting SK Neon Meters
So, took me a couple hours but i did figure it out .
Right down the bottom of the text document was the definitions of what is listed and i just put the ";" in front of all the stuff that was causing me grief and voila.
I adjusted the Y coordinate to close the gap and rearrange to how i like.
now i just need to figure out how to reduce the shape of the skin to fit these new changes to make it look perfect. slowly getting there.
Right down the bottom of the text document was the definitions of what is listed and i just put the ";" in front of all the stuff that was causing me grief and voila.
I adjusted the Y coordinate to close the gap and rearrange to how i like.
now i just need to figure out how to reduce the shape of the skin to fit these new changes to make it look perfect. slowly getting there.
-
- Posts: 1
- Joined: September 27th, 2021, 8:27 am
Re: Help editting SK Neon Meters
Hey. Thanks! I deleted GPU2 thingy following your advice. Have you figured out how to reduce the shape of the skin? I need to fit it on my smaller 2nd monitor without clicking "refresh" every time. No luck editing the txt so far... If you know a solution please message me on discord CptEngage#8797
-
- Posts: 1140
- Joined: February 17th, 2011, 7:45 pm
- Location: a Galaxy S7 far far away
Re: Help editting SK Neon Meters
Depends on the type of meter.
If it's an image meter, usually height and width will adjust the size.
If it's a shape meter, it is a little different. Find the relevant section, and you'll see something like this:
The two zeros are position X and Y.
The two 50's are W and H.
If it's a Roundline meter, you need to adjust the LineStart and LineEnd keys to adjust it's size.
Hope that helps.
If it's an image meter, usually height and width will adjust the size.
If it's a shape meter, it is a little different. Find the relevant section, and you'll see something like this:
Code: Select all
Meter=Shape
Shape=Ellipse 0,0,50,50
The two 50's are W and H.
If it's a Roundline meter, you need to adjust the LineStart and LineEnd keys to adjust it's size.
Hope that helps.
- MuLab -
-
- Rainmeter Sage
- Posts: 16164
- Joined: October 11th, 2010, 6:27 pm
- Location: Gheorgheni, Romania
Re: Help editting SK Neon Meters
No, actually the two 50's are the radiuses, in case of an ellipse. The first two parameters are CenterX and CenterY, so the position of the center as you said, but the third and fourth parameters are RadiusX and RadiusY, not the width and height. The width and height of the ellipse are twice the radiuses. Accordingly in this case they are 100 and 100.sl23 wrote: ↑September 27th, 2021, 9:46 am If it's a shape meter, it is a little different. Find the relevant section, and you'll see something like this:The two zeros are position X and Y.Code: Select all
Meter=Shape Shape=Ellipse 0,0,50,50
The two 50's are W and H.
-
- Posts: 1140
- Joined: February 17th, 2011, 7:45 pm
- Location: a Galaxy S7 far far away
Re: Help editting SK Neon Meters
Ah ok, sorry, I'm used to using rectangles for shapes, even circles as discussed before thought it was the same deal with ellipse!
- MuLab -
-
- Rainmeter Sage
- Posts: 16164
- Joined: October 11th, 2010, 6:27 pm
- Location: Gheorgheni, Romania
Re: Help editting SK Neon Meters
Well, circles are in fact particular ellipses