Matth wrote:I did implement your suggestions, although the substitute one didn't work. It said invalid substitute and the skin wouldn't work anymore.
Then doesn't change your code. Finally using the BaseString, BaseStringUTC and BaseTime variables, is not a too great problem and this won1t create any trouble.
Matth wrote:The TogglePause seems to work, although after the pause, it doesn't continue at the same place. It seems it's continuing in the back and picks up at a random place. Not too annoying, but still not what I was expecting.
Normally. When you pause the [MeasureTimer] measure, the COUNT (COUNTER) function continues to be updated, even if the measure is paused. COUNT returns the number of updates, since the skin was loaded. Its value doesn't depend on the fact if the measure is or isn't paused. That's why it continues to increase, even if you pause the [MeasureTimer] measure.
Fixing this is very simple: you should use another function. So, replace the existing Formula option of the [MeasureTimer] measure, with the following one:
Code: Select all
[MeasureTimer]
...
Formula=(( MeasureTimer % ( #MeaC1# + #MeaC2# + #MeaC3# + #MeaC4# + #MeaC5# + #MeaC6# + #MeaC7# + #MeaC8# + #MeaC9# + #MeaC10# + #MeaC11# + #MeaC12# + #MeaC13# + #MeaC14# + #MeaC15# + #MeaC16# + #MeaC17# + #MeaC18# + #MeaC19# + #MeaC20# + #MeaC21# + #MeaC22# + #MeaC23# + #MeaC24# + #MeaC25# + #MeaC26# + #MeaC27# + #MeaC28# + #MeaC29# + #MeaC30# + #MeaC31# + #MeaC32# + #MeaC33# + #MeaC34# + #MeaC35# + #MeaC36# + #MeaC37# + #MeaC38# + #MeaC39# + #MeaC40# + #MeaC41# + #MeaC42# + #MeaC43# + #MeaC44# + #MeaC45# + #MeaC46# + #MeaC47# + #MeaC48# + #MeaC49# + #MeaC50# + #MeaC51# + #MeaC52# + #MeaC53# + #MeaC54# + #MeaC55# + #MeaC56# + #MeaC57# + #MeaC58# + #MeaC59# + #MeaC60# + #MeaC61# + #MeaC62# + #MeaC63# + #MeaC64# + #MeaC65# + #MeaC66# + #MeaC67# + #MeaC68# + #MeaC69# + #MeaC70# + #MeaC71# + #MeaC72# + #MeaC73# + #MeaC74# + #MeaC75# + #MeaC76# + #MeaC77# + #MeaC78# + #MeaC79# + #MeaC80# + #MeaC81# + #MeaC82# + #MeaC83# + #MeaC84# + #MeaC85# + #MeaC86# + #MeaC87# + #MeaC88# + #MeaC89# + #MeaC90# + #MeaC91# + #MeaC92# + #MeaC93# + #MeaC94# + #MeaC95# + #MeaC96# + #MeaC97# + #MeaC98# + #MeaC99# + #MeaC100# + #MeaC101# + #MeaC102# + #MeaC103# + #MeaC104# + #MeaC105# + #MeaC106# + #MeaC107# + #MeaC108# + #MeaC109# + #MeaC110# + #MeaC111# + #MeaC112# + #MeaC113# + #MeaC114# + #MeaC115# + #MeaC116# + #MeaC117# + #MeaC118# + #MeaC119# + #MeaC120# + #MeaC121# + #MeaC122# + #MeaC123# + #MeaC124# + #MeaC125# + #MeaC126# + #MeaC127# + #MeaC128# + #MeaC129# + #MeaC130# + #MeaC131# + #MeaC132# + #MeaC133# + #MeaC134# + #MeaC135# + #MeaC136# + #MeaC137# + #MeaC138# + #MeaC139# + #MeaC140# + #MeaC141# + #MeaC142# + #MeaC143# + #MeaC144# )) + 1 )
With this function, when you're unpausing the paused measure, it'll continue to count from its last value.
Matth wrote:It's strange that it doesn't work with you. Since it only downloads a satellite image once every 10 minutes, it should take some time to have a few on your disk to run the animation, but at least the first image should be downloaded immediately.
And yes it's long, but only because of the 144 MeaCX measures. Other than that, it should be quite simple. Well, here's the latest code again.
It still doesn't. Maybe you should pack your config and upload it. I'd like to check it, having the whole config, not just the code.